AMERICAN ABRASIVE METALS CO -- NON-SKID DECK COATING EPOXO 350G PART B  -- 8010-00N027002
<pre>=====================  Product Identification  =====================

Product ID:NON-SKID DECK COATING EPOXO 350G PART B
MSDS Date:08/08/1989
FSC:8010
NIIN:00N027002
Kit Part:Y
=== Responsible Party ===
Company Name:AMERICAN ABRASIVE METALS CO
Address:460 COIT ST
City:IRVINGTON
State:NJ
ZIP:07111
Country:US
Info Phone Num:201-373-7060
Emergency Phone Num:201-373-7060
CAGE:88444
=== Contractor Identification ===
Company Name:AMERICAN SAFETY TECHNOLOGIES INC
Address:565 EAGLE ROCK AVE
Box:City:ROSELAND
State:NJ
ZIP:07068
Country:US
Phone:973-403-2600
CAGE:88444

=============  Composition/Information on Ingredients  =============

Ingred Name:POLYAMIDE RESIN; (POLYAMIDE RESIN BLEND)
Fraction by Wt: 75%

Ingred
    Name:1,2-ETHANEDIAMINE,N'-(2-AMINOETHYL)-N'-(2-((2-AMINOETHYL)AMINO
    )ETHYL)-; (TETRAETHYLENEPENTAMINE)
CAS:112-57-2
RTECS #:KH8585000
Fraction by Wt: 4%

Ingred Name:BUTYL ALCOHOL; (N-BUTYL ALCOHOL)
CAS:71-36-3
RTECS #:EO1400000
Fraction by Wt: 20%
OSHA PEL:100 PPM
ACGIH TLV:S, C 50 PPM; 9293
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:INHAL:DIZZINESS, UNCONSCIOUSNESS.
    SKIN: IRRITATION. EYE: IRRITATION, EYE DAMAGE.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:RESPIRATORY DISEASES, SKIN
    CONDITIONS, KIDNEY OR LIVER DISEASES.

=======================  First Aid Measures  =======================

First Aid:INHAL:FRESH AIR, O2, ARTF RESP. SKIN: WASH WITH SOAP AND
    WATER. EYES: FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MIN.
    GET MED ATTN. INGEST:DO NOT INDUCE VOMIT. CALL PHYS.

=====================  Fire Fighting Measures  =====================

Flash Point Method:PMCC
Flash Point:100F,38C
Lower Limits:1.4%
Upper Limits:11.2%
Extinguishing Media:CHEMICAL FOAM OR DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:VAPORS ARE HEAVIER THAN AIR; MAY TRAVEL
    ALONG GROUND AND BE IGNITED BY FLAMES, SPARKS OR OTHER IGNITION
    SOURCES.

==================  Accidental Release Measures  ==================

Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES (FLAMES,
    FLARES, PILOT LIGHTS, ELECTRICAL SPARKS).
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:WARNING! IRRITANT: DO NOT GET IN EYES.
    AVOID CONT W/SKIN/CLTHG. AVOID INHAL OF VAP/MIST. USE W/ADEQ VENT.
    REMOVE CONTAMD CLTHG & WASH BEFORE REUSE.
Other Precautions:WASH THOROUGHLY AFTER HANDLING, AND BEFORE EATING,
    DRINKING OR SMOKING. AVOID EXTREME HEAT-KEEP AWAY FROM FLAME. DO
    NOT EXCEED 100F IN STORAGE AREA.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:IF TLV'S ARE EXCEEDED, NIOSH/MSHA APPROVED SCBA.
Ventilation:LOCAL EXHAUST SUFFICIENT TO MAINTAIN LEVEL BELOW TLV.
Protective Gloves:RUBBER OR BUNAN.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:TO PREVENT REPEATED OR PROLONGED SKIN
    CONTACT, WEAR PROTECTIVE CLOTHING.
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING, AND BEFORE
    EATING, DRINKING OR SMOKING.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

==================  Physical/Chemical Properties  ==================

HCC:F6
Boiling Pt:B.P. Text:243F,117C
Vapor Pres:5@20C
Vapor Density:2.6
Spec Gravity:0.97
Evaporation Rate &amp; Reference:0.7(BUTYL ACETATE=1)
Solubility in Water:MODERATE
Appearance and Odor:VISCOUS LIQUID, AMINE ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG ACID, OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:CO2, CO, NOX, TOXIC FUMES WHEN
    BURNING.

====================  Disposal Considerations  ====================

Waste Disposal Methods:ABSORB ON SAND, CLAY OR OTHER ABSORBANT MATERIAL
    AND SHOVEL INTO CONTAINERS. DISPOSE BY CONTROLLED BURNING OR
    AUTHORIZED LANDFILL. DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE
    AND LOCAL REGULATIONS (F P N).

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.